Services

 

 

On this page below you will discover some amazing resources when it comes to How to Install a Bathtub Yourself.

Installing a tub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also often, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough job. If the old tub is conveniently available, the project can relocate rapidly; if you have to open up a wall to remove the old bathtub and place the brand-new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have qualified on your own for the task as well as are comfortable trying it. Rather than working with a professional to take over a halfway-completed project, it is far better to take into consideration using one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your washroom if you have actually already bought a brand-new tub and do not require to transform the plan of your previous supply of water pipes.
Your tools and also product list must make up the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Planning for the Setup

Firstly, the sustaining framework supplied with the bath should be fitted (if called for) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable tap adapters to the bottom of both faucets utilizing 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be suited its final position.

 

 

Removing Old Touches

If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather problematic as a result of the limited access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.

 

 

Installing the Bath tub

Using both wooden boards under its feet, place the bath tub in the required setting. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub till the spirit level reads degree.
To install faucets, fit the bottom of the outermost flexible tap adapter to the suitable supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water as well as examine all joints and brand-new pipework for leakages and tighten them if essential. Fill the tub as well as also inspect the overflow outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bath tub has been utilized at the very least when as this will settle it right into its final setting.

 

 

Fitting New Taps

If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin ensuring that the washers are in location in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer offered backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have been connected.

 

 

Tiling Around the Bathtub

In the area where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about difficulties with wetness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always load the bath tub with water before sealing, to permit the motion experienced when the bathtub remains in use. The sealer can split fairly very early if you do not consider this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof glue and cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I hope you enjoyed our section on How to Install a Bathtub. Thanks a ton for spending some time to read our piece of content. Sharing is caring. Who knows, you may be helping someone out. Thanks for your time. Don't hesitate to visit our site back soon.

Estimate